Getbig.com: American Bodybuilding, Fitness and Figure
Getbig Bodybuilding Boards => Steroids Info & Hardcore => Topic started by: NY MUSCLE on January 26, 2012, 06:32:38 PM
-
Do any of you guys warm your gear before injections?
-
No need to..
-
why unless its crashed gear wich I wouldnt shoot anyway.
-
^^^^
-
Do any of you guys warm your gear before injections?
i had to with test cypionate. and it was legit(!) i gained 34 lbs in 12 weeks on it plus deca and a little dbol. but that's just how cypionate works. it has the tendency to fall out of suspension. test crystals separated from the oil. i would have to heat it every time in order for it to re homogenize.
-
Thanks for the input, i don't know if it's just me, but i feel it allows the oil to go into the muscle with ease. I use the wife's hair dryer and things seem to go smooth
-
some oils are thick as fuck... ive had a few different brands on enth where ive had to warm the vials under a warm tap or id be trying to shoot for 5 mins!
ive got a few boxes of cidoteston left that will have to be done the same way when i go back on... oh, and ive been off 5 weeks and im down 21lbs
-
always, goes in much easier!
-
Always...
I use a flat iron used for hair with a rubber band on the end to hold the ends together.
I put two vials in at the start of my shower and when I am done, it is hot and goes in smooth as silk.
All 2 grams worth.
War
-
never do that.
-
I run my syringe under hot water to just thin the oil out so it goes in smoother.
-
never do that.
Meaning "I don't do that" or "don't do that".
If the later...why?
War
-
hell no. what a waste of time
-
hell no. what a waste of time
x2
-
hell no. what a waste of time
Terrible waste of time. ::)
You can warm it while you are brushing your teeth.
-
hell no. what a waste of time
LOL...everyone is in hurry to get big.
Seconds count!!!!
War
-
LOL...everyone is in hurry to get big.
Seconds count!!!!
War
youve obviously not used hg enth, its thick as fuck, you almost bruise your thumb pushing it in
-
i used to when i first started out and had some really crappy test. it was brewed up well above the point of what the solvents could hold and would crash a tiny bit, giving PIP for a few days post injection. heating it and then cutting it with EQ seemed to help a lot.
now, i don't feel the need since nothing i use can't flow through a slin pin.
-
youve obviously not used hg enth, its thick as fuck, you almost bruise your thumb pushing it in
True.
All the HG Test amps I have used over the years were very thick. Even with a 23g pin it takes a lot of pressure to get the plunger moving.
Some of the UGL stuff i've used was like shooting water.
8)
-
I shoot ED with 25g pins, 1 minute of warming under a hot faucet just makes it go in smoother.
I warm the syringe, not the vials. Take exactly 1 min, no problem.
-
youve obviously not used hg enth, its thick as fuck, you almost bruise your thumb pushing it in
Hah..I am heating my gear prior to pining. I hate standing there jamming 3 mls of cold oil into my quad or ass. Takes forever if you have 6 more mls to pin for you daily run. Especially if it is thick grape seed oil or EOL.
War
-
Some gear especially extra thin oil can clog a plunger and cause more friction, resulting in much longer pin time. I've found that putting the loaded syringe under my hot water faucet for a minute than running into my room to inject makes it much easier/faster/less painful. It's pretty much only the 5ml syringes that clog. The 3ml's usually don't
-
if you need to warm your gear it isn't pharma grade, you need to get quality gear.
-
ethyl oleate FTW
-
ethyl oleate FTW
How come? Not grapeseed? Ethyl Oleate has the strong ass smell lol
-
thin and painless, able to hold higher concentrations of gear without crashing.
-
I run my syringe under hot water to just thin the oil out so it goes in smoother.
This quite often.
-
some oils are thick as fuck... ive had a few different brands on enth where ive had to warm the vials under a warm tap or id be trying to shoot for 5 mins!
ive got a few boxes of cidoteston left that will have to be done the same way when i go back on... oh, and ive been off 5 weeks and im down 21lbs
what gauge syringe were you using?
-
I run my syringe under hot water to just thin the oil out so it goes in smoother.
Me, too. Especially when using 28G slinpins for delt & arm shot. I just run very hot water over the syringe (w/ cap on needle) while tilting it back and forth until the air bubble moves noticeably faster through the oil. I guess it takes about 30 - 40 seconds.
-
i used to when i first started out and had some really crappy test. it was brewed up well above the point of what the solvents could hold and would crash a tiny bit, giving PIP for a few days post injection. heating it and then cutting it with EQ seemed to help a lot.
now, i don't feel the need since nothing i use can't flow through a slin pin.
bro what kind of brewing formula is your guy using please pm me if you know cause a slin pin would be awesome, way less scar tissue. :) :) :)
-
do you just use same formula to brew but us eol instead of oil??