Getbig.com: American Bodybuilding, Fitness and Figure

Getbig Bodybuilding Boards => Steroids Info & Hardcore => Topic started by: muscle19 on February 14, 2006, 08:43:45 PM

Title: injection site
Post by: muscle19 on February 14, 2006, 08:43:45 PM: hey bros, did a delt injection today and i noticed gear leaking through the hole, is that normal? it looked like alot was coming out of where i put the needle. thanks in advance

muscle
Title: Re: injection site
Post by: Arnold jr on February 14, 2006, 09:08:06 PM: Quote from: muscle19 on February 14, 2006, 08:43:45 PM
hey bros, did a delt injection today and i noticed gear leaking through the hole, is that normal? it looked like alot was coming out of where i put the needle. thanks in advance
muscle

What size pin? Are you injecting all the way in applying pressure? Are you applying pressure immediately after injecting...you should be if not.
Title: Re: injection site
Post by: ag-guys on February 14, 2006, 10:20:20 PM: Quote from: muscle19 on February 14, 2006, 08:43:45 PM
hey bros, did a delt injection today and i noticed gear leaking through the hole, is that normal? it looked like alot was coming out of where i put the needle. thanks in advance
muscle

If it leaks a little, that is ok, do not worry.

AG
www.ag-guys.com
Title: Re: injection site
Post by: DIVISION on February 15, 2006, 01:55:59 AM: Quote from: muscle19 on February 14, 2006, 08:43:45 PM
hey bros, did a delt injection today and i noticed gear leaking through the hole, is that normal? it looked like alot was coming out of where i put the needle. thanks in advance

It means you didn't go balls deep, bro.

As if I hadn't emphasized it enough on here.

When you inject PRESS BALLS KEEP. >:(

Keep the pressure on throughout the injection and hold it in for about 10 seconds after the oil is through to keep the oil in.

Then pull out.

DIV
Title: Re: injection site
Post by: Hitman_Forhire on February 15, 2006, 08:11:51 AM: BALLS DEEP!....That's the ONLY way to do things in life, IMHO....
Title: Re: injection site
Post by: muscle19 on February 15, 2006, 04:47:41 PM: i use 3/4in needle for delts but usually dont have a problem, and i do hold in in there to make sure the gear went through, no lumps as if i injected into under the skin. would i be better off using 1in?

muscle
Title: Re: injection site
Post by: Arnold jr on February 15, 2006, 08:52:23 PM: Quote from: muscle19 on February 15, 2006, 04:47:41 PM
would i be better off using 1in?
muscle
Yes, 1" 23g-25g
Title: Re: injection site
Post by: muscle19 on February 15, 2006, 09:49:20 PM: thanks alot guys, there is always something to learn, i usually have no problems with that size but this time, too much gear came out.

muscle
Title: Re: injection site
Post by: DIVISION on February 16, 2006, 02:26:22 AM: Quote from: muscle19 on February 15, 2006, 04:47:41 PM
i use 3/4in needle for delts but usually dont have a problem, and i do hold in in there to make sure the gear went through, no lumps as if i injected into under the skin. would i be better off using 1in?
muscle

I use 1" 25G.

Yes.......balls deep.

No lumps.....

DIV
Title: Re: injection site
Post by: cypher on April 19, 2008, 12:31:27 PM: Having the same problem, only with delt injections.. I use 1" 22 gauge pins. I do go 'balls deep' and apply pressure, inject slowly and pull it out slowly.. I also get little red 'dots' right around injection site immediately after..